Digi-Code Model CR2149 Universal Beam Sensor Model CR2149 Universal Beam Sensor The universal beam sensor works with all major brands of garage door openers - Chamberlain®, Liftmaster®, Craftsman™, Overhead® (1995+), Genie™, Challenger®, Stanley®, Linear®, Moore-O-Matic® and Raynor® models ( built by Chamberlain® ). The beams have a self programming feature which allow the installer to simply hook up the beams to the existing wiring, mount the units to the wall and the job is complete. This unique product provides the following features: Superior filtering from sunlight Reduces your inventory of replacement beams Competitively priced Quick retrofit installation Non-polarized ( so there is no way to hook them up backwards ) Now you can go out to a job site with one of these universal beams on the truck and feel comfortable that you can solve the beam sensor problems without having to return. The Universal Replacement Beam Sensor Kit includes: One Sender and One Receiver Module Two Mounting Brackets Four Wood Screws Instruction Sheet
With so many on offer these days, it is great to have a name you can trust. This item is certainly that and will be a perfect buy. The distributor have added some great touches and this equals great value.
You can trust this review, i hope you can try to buy this product and then you know this product good or no. Next time you can make a review for another people.
Works Fine, but poor installation instructions
This works fine and was easy to install, but there were only two terminals on one sensor where my old sensor had four wires connected. The installation instructions said nothing about this so I had to use trial and error to figure out how to connect it. If you have the same problem, simply connect both "+" wires from the old sensor to the "+" terminal on the new sensor and both "-" wires from the old sensor to the "-" terminal on the new sensor.
Click here to read the full review for more information about this product.
Beamers work for Stanley Vemco
I purchased two sets of the beamers for my 1998 Stanley Vemco doors. Had trouble with the origial safety sensors and was sick of holding the button to close so it was time to fix. Received the units in about three days. The old receiver has 4 wire but you can just twist the + together and the - together to make it work for the two wire Digi-Code. I opened the box, cut the "black" wire on the receiver as instructed for the Stanley brand, then installed for a test run-Nothing! They did not work. I was baffled so a tried changing the wires around but still nothing worked (you can hook them up backwards and it will not hurt the units). I then tried the "Sender" on the wire coming down from the opener motor (has low voltage power) and the red light lit up. I then twisted the wire together with the wire going over to the other side of the door and hooked the sender up over there - DEAD! Ahah! Now I knew what was wrong; the wire was damaged in the atic somewhere (mice?). I ran to the...
Worked like a charm thanks to other reviews
I was using this device to replace yellow Moore-O-Matic sensors. I agree with other reviewers that the instructions are totally inadequate if you are replacing sensors for a Moore-O-Matic. The receiver on the old sensor has four wires, the new unit only two; and the instructions mention nothing about this. Another reviewer said that you needed to hook both positives of the old receiver (one labeled "to emitter," the other labeled "to operator") to the single positive of the Digi-Code receiver and both negatives from the old reciever to the single negative of the Digi-Code receiver (You also need to cut the yellow wire on the back of the new receiver as it says in the Digi-Code instructions). He said you needed to switch the position of the emitter and receiver, but I found that was not necessary and wonder if the reviewer had some location specific issues (my doors face south and do not get any direct sun). Once the wires were attached, the doors worked perfectly. When the...
Product Features :
- universal beam sensor works with all major brands of garage door openers such as -
- Chamberlain®, Liftmaster®, CraftsmanTM, and
- Overhead® (1995+), GenieTM, and
- Challenger®, Stanley®, Linear®, Moore-O-Matic® and Raynor® models ( built by Chamberlain® ).
- Self programming feature which allow the installer to simply hook up beams to the existing wiring.
Rating : 4.1
List Price : $28.00
0 comments:
Post a Comment